Alto-Shaam QC-50 Operations Instructions Page 13

  • Download
  • Add to my manuals
  • Print
  • Page
    / 29
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 12
AT-A-GLANCE
QC-50 CONTROL SETTINGS
PRINTER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Printer Interface = Serial
Baud Rate = 4800
Stop Bits = 1 bit
Printing Delay = 40 [40]
Sample Period, min. = 5 [ 5]
Print Grid Spacing = 5 [ 5]
Print Grids = YES
Printer Columns = [40]
BUZZERS/TIMEOUTS . . . . . . . . . . . . . . . . . . . . . . . . . .
Probe Mute Time, sec. = 30 [30]
Chill Done Time, sec. = 60 [60]
Are-U-Sure Time, sec. = 20 [20]
DefrstDone Time, sec. = 60 [60]
Probe Mute Buzzer = 0 [ 0]
Chill Done Buzzer = 1 [ 1]
Are-U-Sure Buzzer = 2 [ 2]
Defrost Done Buzzer = 3 [ 3]
HOLDING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hold Set-point, C = 3 [ 3]
Hold Offset, 0.1C = 0 [ 0]
Hold Low Offset, 0.1C = 6 [ 6]
Hold Med Offset, 0.1C = 4 [ 4]
HoldHigh Offset. 0.1C = 4 [ 4]
CHILLING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Probe 1 Set-point, C = 4 [ 4]
Probe 2 Set-point, C = 4 [ 4]
Probe 3 Set-point, C = 4 [ 4]
Chill Set-point, C = -6 [- 6]
Chill Offset, 0.1C = 0 [ 0]
ChillLow Offset. 0.1C = 8 [ 8]
ChillMed Offset, 0.1C = 8 [ 8]
ChillHi Offset. 0.1C = 8 [ 8]
DEFROSTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Automatic Defrost = YES
AutoDefrst Per. 5min = 72 [72]
DefrstWarnTime, 10min = 60 [60]
Coil1 Defrost End. C = 16 [16]
Coil2 Defrost End, C = 16 [16]
Defrost Time, min = 20 [20]
MISC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chiller Model = QC-50
Compressor Mode = CPU CNTR
Number Compressors = TWO
Power Throttle = YES
Temp Cycling = YES
RTD Offset, 0.1C = 0 [ 0]
Power Down Minutes = 1 [ 1]
Temperature Units = Farhen
Time Format = HH:MM
Fan Cut-in Temp, C = 4 [ 4]
Fan Cut-Out Temp, C = 13 [13]
KeyBoard Buzzer = ON
Device Access Number = 49 [49]
NOTE: [ ] = DEFAULT VALUES
#8400 Installation & Maintenance Manual - Pg. 11
Page view 12
1 2 ... 8 9 10 11 12 13 14 15 16 17 18 ... 28 29

Comments to this Manuals

No comments